Prescolite D2ICAT Manuel d'utilisateur télécharger pdf

Instruction

Sheet

Part No...........................................

With representatives offices in principal cities throughout North America.

701 Millennium Blvd., Greenville, SC 29607

www.prescolite.com y Prescolite Toll Free Technical Support 1.888.PRS.4TEC y Hours: 8am - 5pm ET

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information

and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,

and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and

during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.

Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in

compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended b

the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from

product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens o

the like to come into contact with the product or to block li

ht from the product, as this ma

cause an unsafe condition.

93040526

2012

01/25/12

WARNING

–

This product contains chemicals known to the State of California to cause cancer, birth defects and/or othe

reproductive harm. Thorou

wash

our hands after installin

, handlin

, cleanin

, or otherwise touchin

this product.

CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND

PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.

KEEP THESE INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

MODEL D2ICAT

1. The bar hanger brackets are sh ipped flat. Bend the ta b s on

the brackets a s show n to allow the use of a cce sso ry m ounting

channels or bar hangers (Presco lite B6, B24, or by others).

M ount the fram e in the ceiling so that the w eight of the

a sse m b ly is sa fely supported by the m ounting channel or bar

and/or hanger wire s secured to the building structure.

2. Rem ove the top of the h o u sing and adju st the fram e so the

bottom su rface is flu sh with the ceiling m aterial m ounting

su rfa ce (backside of the ceiling m aterial) and in alignm ent

with adja cent fixture s. The rivets for the 8 ” x 8 ”

polyca rbonate cut-through panel m ay be used a s centerlines

(a s show n) for aligning the fram e. Secure the m ounting

bra ckets by tightening wing nuts on either side of the fram e

in side the D2IC A T h o using.

3. Important! When the ceiling material is added

(covering the D2ICAT) make sure the D2ICAT is

flush with the back side of the ceiling material and

solidly mounted. Mark the fixture installation

location accurately so the hole cut-through location

will be accurate!

4. There are four 3/8” M C flexible conduit entry points located

on the rear cover plate of the D2IC A T to allow the

UNENERGIZED line voltag e and

control (0-10V dimming)

flexible conduit to be inserted into the h o u sing until they are

used w hen the D2LED fixture is wired and in stalled. There are

four conduit g a sk ets included with the D2IC A T h o u sing to be

used if needed to se a l the conduit opening further after the

flexible conduit is in stalled. Th ere is also a tether cable

m ounted in side the h o u sing to be attached to the D2LED

fixture in the ca se of se ism ic conditio n s at the in stall location.

This tether, if needed, sh o uld be attached to the screw on the

light engine (see Figure A) after the wiring is com plete and

the J-tube is inserted in the ceiling, but before fixture is

in stalled.

5. In stall the D2LED fixture per the in struction sheet pro vided with

the fixture. W hen the hole is cut in the ceiling with the 2-7/8”

hole sa w (by others), it will cut through the ceiling m aterial

and the D2IC A T polycarbonat

e cut-through panel at the sa m e

tim e pro viding accurate alignm ent in both the ceiling m aterial

and the D2IC A T.

6. WARNING: DO NOT pinch wires between J-tube

cover and J-tube endplates. Consult a Qualified

Electrician for all other options that require other

wiring configurations.

DETAIL A

D2ICAT WITH D2LED INSTALLED

8" x 8"

Polycarbonate

Panel

Cut-Through

Area

Siesmic

Tether

D2LED

Fixture Screw

3/8" Flexible

Conduit

Entry Points

Extra

Conduit

Gaskets

InstructionSheet

www.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ET

701 Millennium Boulevard • Greenville, SC 29607

With representatives offices in principal cities throughout North America.

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93040526

InstructionSheet

INSTALLATION INSTRUCTIONS

MODEL D2ICAT

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and

instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and

proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and during

servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other poten-

tial hazard. Product must be mounted in locations and at heights and in a manner consistent with its

intended use, and in compliance with the National Electrical Code and local codes. The use of accessory

equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do

not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such

as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as this may

cause an unsafe condition.

WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects and/or other

reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND

PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.

KEEP THESE INSTALLATION INSTRUCTIONS

1. The bar hanger brackets are shipped flat. Bend the tabs on the

brackets as shown to allow the use of accessory mounting channels

or bar hangers (Prescolite B6, B24, or by others). Mount the frame

in the ceiling so that the weight of the assembly is safely supported

by the mounting channel or bar and/or hanger wires secured to

the building structure.

2. Remove the top of the housing and adjust the frame so the bottom

surface is flush with the ceiling material mounting surface (backside

of the ceiling material) and in alignment with adjacent fixtures.

The rivets for the 8” x 8” polycarbonate cut-through panel may be

used as centerlines (as shown) for aligning the frame. Secure the

mounting brackets by tightening wing nuts on either side of the

frame inside the D2ICAT housing.

3. Important! When the ceiling material is added (covering

the D2ICAT) make sure the D2ICAT is flush with the

back side of the ceiling material and solidly mounted.

Mark the fixture installation location accurately so the

hole cut-through location will be accurate!

4. There are four 3/8” MC flexible conduit entry points located on the

rear cover plate of the D2ICAT to allow the UNENERGIZED line

voltage and control (0-10V dimming) flexible conduit to be inserted

into the housing until they are used when the D2LED fixture is wired

and installed. There are four conduit gaskets included with the

D2ICAT housing to be used if needed to seal the conduit opening

further after the flexible conduit is installed. There is also a tether

cable mounted inside the housing to be attached to the D2LED

fixture in the case of seismic conditions at the install location. This

tether, if needed, should be attached to the screw on the light

engine (see Detail A) after the wiring is complete and the J-tube is

inserted in the ceiling, but before fixture is installed.

5. Install the D2LED fixture per the instruction sheet provided with

the fixture. When the hole is cut in the ceiling with the 2-7/8”

hole saw (by others), it will cut through the ceiling material and

the D2ICAT polycarbonate cut-through panel at the same time

providing accurate alignment in both the ceiling material and the

D2ICAT.

6. WARNING: DO NOT pinch wires between J-tube cover

and J-tube endplates. Consult a Qualified Electrician

for all other options that require other wiring

configurations.

Seismic

InstructionSheet 1

Résumé du contenu

Page 1 - InstructionSheet

InstructionSheetPart No............With representatives offices in principal cities throughout North America.Copyright

Commentaires sur ces manuels

Pas de commentaire

Prescolite D2ICAT Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Prescolite D2ICAT. Prescolite D2ICAT User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Prescolite D2ICAT