Prescolite IBX5 Manuel d'utilisateur télécharger pdf

Instruction

Sheet

Part No...........................................

With representatives offices in principal cities throughout North America.

701 Millennium Blvd., Greenville, SC 29607

www.prescolite.com



Prescolite Toll Free Technical Support

1.888.PRS.4TEC



Hours: 8am - 5pm ET

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and instructions

concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and proper lamping

. Do not

install in areas subject to combustible vapors or gases. Before wiring to power supply and during servicing or relamping, turn off pow

er at

fuse or circuit breaker. All servicing or relamping must be performed by qualified service personnel. Product must be grounde

d to

avoid potential electric shock or other potential hazard. Product must be mounted in locations and at heights and in a manner

consistent with its intended use, and in compliance with the National Electrical Code and local codes.

The use of accessory

equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not bloc

k light

emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains

, screens or

the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

93010075

Sheet 1 of 2

2012 09/25/12

INSTALLATION INSTRUCTIONS

IBX5

WARNING:

Thermal insulation may be installed in direct contact with the fixture, but DO NOT install insulation in excess of

eight inches deep above fixture. Greater depth may cause the thermal protector to cycle the fixture on or off.

WARNING:

Use only those trims, lamps, and maximum wattages proper for this fixture, as indicated on the label within the

housing (3).

WARNING: National Electrical Code, Article 110-3 (b), states that “Listed or labeled equipment shall be used o

r installed in

accordance with any instructions included in the listing or labeling”. Use only Prescolite UL listed trims. Use of other trim

not listed in this fixture, including those that are UL classified, is a violation of N.E.C. 110-3 (b) and voids all warranties.

WARNING:

This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other

reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

WARNING: If any special control devices are used with this fixture, follow the instructions carefully to assure full

compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.

1. For Wooden Joists: Extend the Bar Hangers (6), use joist alignment tabs (4) to locate fixture and position the alignment

tabs (4) underneath support joist (8). Drive the 4 Nails (7) into Joists (8) (Fig. 1). Drive additional nails through holes in Bar

Hanger for alternate support if required.

2. For Suspended Ceilings: Place the Fixture on the ceiling grid with the "T" Bars (9) running through the Bar Hanger

Notches (10). Using a flat head screwdriver or other tool, bend the integral t-bar mounting tabs (11) downward to a vertical

position (Fig. 3). Secure housing to the support structure with tie wire (supplied by others) in the holes supplied.

Sheetmetal screws (supplied by others) can also be used in the holes supplied (20).

3. Locate Housing along Bar Hanger in desired position and, using pliers, squeeze the 4 Locking Tabs (12) on the Plaster

Frame (13) tightly over the Bar Hangers to prevent further Housing movement. Set Screws (1) are provided that can be

tightened to lock the Housing (3) on the Bar Hangers (6).

4. As desired, hanger bars (6) may be shortened at score mark to fit tight mounting conditions and joist alignment tabs

removed to adjust vertically as needed by breaking off with pliers.

5. Unsnap Junction Box Cover (14) by lifting the Leaf Spring (24).

6. Run supply wires through UL Listed connectors (not supplied) in one of the five Pryouts (15) on the Junction Box (16) or

Type NM cable (ROMEX) through an Opening above the Wire Retaining Plate (17). Connect Supply Wires (19) as shown

in Fig 4 & 5. Replace Cover.

7. FOR AIR-TIGHT APPLICATIONS: This Prescolite product is Air-Tight approved per ASTM E283 testing standards and

complies with Washington State Energy Code Requirements. To complete the installation of this Air-Tight product, the

opening between the housing (3) and drywall ceiling (22) must be sealed by the installer using silicone caulking, tape, or

any other means acceptable to the local codes official. Prescolite accessory gasket kit G6 (purchased separately) can be

used for this purpose (Fig. 6).

8. Select a Trim from the Wattage Label inside the Housing. Use Only Lamp Types approved for the Trim chosen. DO

NOT EXCEED MAXIMUM LISTED WATTAGE(S)!

9. To gain access to junction box (16) after ceiling is finished, remove three screws (21) that hold the housing (3) in place.

Lower the housing. Remove screw (2) and access door (25

) located inside housing. Junction box cover place (14) can now

be removed.

SOCKET CAP AND INSTRUCTION SHEET MUST BE REMOVED FROM FIXTURE PRIOR TO ENERGIZING.

1 2

Instruction 1

Résumé du contenu

Page 1 - Instruction

InstructionSheetPart No....With representatives offices in principal cities throughout North America.Copyright

Page 2

InstructionSheetPart No............With representatives offices in principal cities throughout North America.Copyright

Commentaires sur ces manuels

Pas de commentaire

Prescolite IBX5 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Prescolite IBX5. Prescolite IBX5 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Prescolite IBX5