Prescolite LB6LEDA10L Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Prescolite LB6LEDA10L. Prescolite LB6LEDA10L User Manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Instruction
Sheet
Part No...........................................
With representatives offices in principal cities throughout North America.
Copyright , revision, All Rights Reserved - Printed in U.S.A.
701 Millennium Blvd
•
Greenville, SC 29607
www.prescolite.com
Prescolite Toll Free Technical Support
1.888.PRS.4TEC
Hours: 8am - 5pm ET
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and instructions
concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and proper lamping
. Do not
install in areas subject to combustible vapors or gases. Before wiring to power supply and during servicing or relamping, turn off pow
er at
fuse or circuit breaker. All servicing or relamping must be performed by qualified service personnel. Product must be grounde
d to
avoid potential electric shock or other potential hazard. Product must be mounted in locations and at heights and in a manner
consistent with its intended use, and in compliance with the National Electrical Code and local codes.
The use of accessory
equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not bloc
k light
emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains
, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
93039951
2013 06/04/13
••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
•••••
•
WARNING – Follow the Instruction carefully to assure full compliance with local, state, and NEC requ
irements. If there are any questions,
contact a Qualified Electrical Contractor.
WARNING – Risk of fire or electrical shock. Install this kit only in Recessed Cans matching the dimensions in Table A below.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges sheet metal or sharp objects.
WARNING – Risk of fire. Consult a Qualified Electrician to ensure correct branch circuit conductor.
NOTE – This product is designed to operate with most standard incandescent or low voltage electronic dimmer switches. Results may
vary. For recommended dimmers, consult product spec sheet or go to www.prescolite.com or call Technical Support 1-888-PRS-4TEC.
NOTE – SUITABLE FOR WET LOCATIONS IN COVERED CEILINGS
WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other reproductive
harm. Thoroughly wash your hands after installing, handling, cleaning, or otherwise touching this product.
NOTE – Always install within ambient temperatures specified on the product specification sheet. 5 year warranty.
See www.prescolite.com for details.
••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••••••
•
••••
INSTALLATION INSTRUCTIONS
LB6LEDA / LB6LEDA10L SERIES
Fits into Prescolite 6” recessed cans including: DBX, RMNICD, IBXHW, FT6, IBXS, RMNICS. Fits into most competitive recessed cans
with “A” and “B” dimensions above including: Halo H7ICAT, H7RICAT; Juno IC22; Lithonia L7X; Capri CR1, CRR1; Progress P87
-AT,
P87-ATQC, P187-TG, P821-FB; Nora NHIC-17QAT, NHRIC-17QNBAT; Sea Gull 1128. See www.prescolite.com for more details.
IMPORTANT! Prior to retrofit installation, recessed can must be properly installed and flush with the ceiling. It may be necessary to
detach the socket from a mounting bracket or spring. Remove and discard bracket to allow adequate clearance.
1. Connect Trim to Power
For retrofit: Screw socket adapter (1) into socket (2) as shown. Or to hard-wire: Cut medium base screw shell socket wires near socket,
discard socket. Cut and remove screw shell adapter from trim, discard adapter. Strip wires and connect (Blk-Blk, Wht-Wht) with UL listed
connectors.
For new construction with dedicated LED housing: Remove socket adapter assy (1) and discard. Connect trim connector (3) directly
to mating LED housing connector (4) as shown.
2. Insert Trim into Recessed Can
Guide socket and wiring toward the can opening. Push trim up into recessed can, while twisting trim counterclockwise ¼ turn, firmly
engaging the spring clips (5) until flush with ceiling. NOTE: Loose wires can be placed in wire trap to avoid interference or pinching of
wiring.
3. To remove trim assembly, twist trim assembly counterclockwise ¼ turn while pulling down.
KEEP THESE INSTRUCTIONS
"A"
"B"
"A" = 6-5/16 MIN. 7-1/8 MAX.
"B" = 5-1/2 MIN.
TABLE A
TWIST TRIM ASSEMBLY
COUNTERCLOCKWISE
1/4 TURN WHILE
PUSHING TRIM INTO CAN
RETROFIT
WIRE TRAP
DEDICATED LED HOUSING
FOR TITLE 24
1
2
5
5
3
4
1
1
2
Résumé du contenu
Page 1 - Instruction
InstructionSheetPart No....With representatives offices in principal cities throughout North America.Copyright
Page 2
InstructionSheetPart No............With representatives offices in principal cities throughout North America.Copyright
Produits connexes et manuels pour Éclairage Prescolite LB6LEDA10L
(1 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels