Prescolite SLLED3 Manuel d'utilisateur télécharger pdf

InstructionSheet

701 Millennium Blvd., • Greenville, SC 29607

With representatives offices in principal cities throughout North America.

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93017298

InstructionSheet

INSTALLATION INSTRUCTIONS

RECESSED LED AISLE LIGHT SLLED3

1. Remove face plate and lens assembly by removing the 6-32 tamper resistant screws and place in bag enclosed.

2. Remove the 6-32 pan head screws securing the LED assembly to the housing and remove the LED assembly and place in

bag enclosed.

3. Remove wire nuts connecting the LED assembly to the driver bracket assembly.

4. Secure the housing appropriately.

a. For concrete pour and masonry construction refer to FIG. 2 and 3.

b. For drywall construction refer to FIG 4, 5, and 6.

5. Connect the black fixture wire from the driver assembly to the black supply wire.

6. Connect the white fixture wire from the driver assembly to the white supply wire.

7. Secure the driver assembly using the 6-32 screws provided.

8. Connect the black wire from the driver assembly to the black wire of the LED assembly using wire nut provided.

9. Connect the red wire from the driver assembly to the red wire of the LED assembly using the wire nut provided.

10. Secure the face plate and lens assembly using the 6-32 tamper resistant screws provided.

WARNING: DO NOT pinch wires between driver bracket and housing. Consult a Qualified

Electrician for all other options that require other wiring configurations.

WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects and/or

other reproductive harm. Thoroughly wash hands after installing , handling, cleaning, or otherwise touching this

product.

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information

and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,

and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and

during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.

Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in

compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by

the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from

product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or

the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

HOUSING

(2) 6-32 PAN HEAD

SCREWS

FACE PLATE AND

LENS ASSEMBLY

(2) TAMPLER PROOF

6-32 BUTTON HEAD

SCREWS.

BLACK AND WHITE WIRE

TO BE CONNECTED TO

SUPPLY WITH UL APPROVED

WIRE NUTS.

LED/DRIVER ASSEMBLY

FIG. 1

1 2 3

InstructionSheet 1

Résumé du contenu

Page 1 - InstructionSheet

Page 2

GASKETTYPICALCONDUITCONNECTIONHOUSINGPart No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93017298InstructionSheet701 Millennium B

Page 3

CONDUITCONNECTIONHOUSINGGASKETTYPICALDRY CONSTRUCTIONPart No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93017298InstructionSheet

Commentaires sur ces manuels

Pas de commentaire

Prescolite SLLED3 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Prescolite SLLED3. Prescolite SLLED3 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Prescolite SLLED3