InstructionSheet
www.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ET
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93012107
InstructionSheet
INSTALLATION INSTRUCTIONS
RDPS6LED SERIES
FIG. 1
W
ING NUT
BEND BRACKETS
IN LINE WITH
M
ARKS ON FLANGE
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other
reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.
701 Millennium Boulevard • Greenville, SC 29607
W
ith representatives of
fices in principal cities throughout North
America.
Copyright 2009, 10/30/09 revision, All Rights Reserved - Printed in U.S.A.
1. BEND BRACKETS AS SHOWN IN FIG 1. INSTALL THE FIX-
TURE IN THE CEILING USING MOUNTING CHANNELS OR
BAR HANGERS (B6, B24, OR BY OTHERS) PLACED IN THE
ADJUSTABLE MOUNTING BRACKETS. MOUNT THE FIXTURE
IN
THE CEILING SO THAT THE WEIGHT OF THE FIXTURE IS
SUPPORTED BY THE MOUNTING CHANNEL OR BAR AND/OR
HANGER WIRES SECURED TO THE BUILDING STRUCTURE
(NOT CEILING). MAKE SURE FIXTURE IS TIGHT AND
SECURE IN CEILING, NOT MOVING.
2. ADJUST THE FIXTURE SO THE BOTTOM EDGE OF THE
PLASTER FLANGE OPENING IS FLUSH WITH THE FINISHED
CEILING LINE AND IN ALIGNMENT WITH THE ADJACENT FIX-
TURES. SECURE MOUNTING BRACKETS BY TIGHTENING
WING NUTS ON EITHER SIDE OF THE FIXTURE. REMOVE
PENDANT BRACKET BY REMOVING (6) 8-32 SCREWS (SUP-
PLIED). SEE FIG 2B. DETERMINE WHICH KNOCKOUT THE
SUPPLY WIRE CONDUIT WILL ENTER THE DRIVER HOUSING
AND CONNECT IT IN COMPLIANCE WITH THE NATIONAL
ELECTRICAL CODE: BLACK TO LINE, WHITE TO COMMON,
AND GREEN TO GROUND. (DIMMING ONLY) CONNECT
GRAY (+) AND VIOLET (-) WIRE FROM DRIVER TO APPRO-
PRIATE 0-10V DIMMING CONTROL (BY OTHERS.) PUSH
WIRE CONNECTIONS MADE TO SUPPLY WIRES INTO
UPPER HOUSING.
WARNING: DO NOT PINCH WIRES. CONSULT A QUALIFIED
ELECTRICIAN FOR ALL OTHER OPTIONS THAT REQUIRE
OTHER WIRING CONFIGURATIONS
3. PULL SAFETY CABLE OUT OF DRIVER HOUSING MAKING
SURE “S” HOOK IS ATTACHED TO FREE TERMINAL HOLE
AND LET IT HANG DOWN. SEE FIG 2C. REPLACE PENDANT
BRACKET
AND F
ASTEN 2 HEX SCREWS (SUPPLIED)
HALFWAY INTO PENDANT BRACKET. SEE FIG 2B.
4. ASSURE THAT RETAINER RING IS PUSHED DOWN OVER
BALL
HAL
VES AND SNAPPED INTO PENDANT COVER
PLATE. SEE FIG 4.
5.
HOLD PENDANT
UP
T
O HOUSING FIXTURE,
ALLOWING
CEILING COVER TO REST AT BOTTOM OF STEM.
FIG. 2B
FIG. 2C
FIG. 2A
SEE FIG 5A
FOR DETAILS
PENDANT
BRACKET
PLASTER
FLANGE
PENDANT
BRACKET
PLASTER
FLANGE
SAFETY CABLE
“S” HOOK
MOUNTING
PLATE
SEE FIG. 5A
FOR DETAILS
KEEP THESE INSTRUCTIONS
(3 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels